How much material do you need? Pick a calculator — enter your measurements and get the quantity, a waste allowance and an estimated cost. No sign-up, no waiting.
Cubic yards, tons and bags for soil, gravel, mulch, drainage and garden beds. (14 calculators)
Concrete volume, bags, block, brick, mortar and rebar for pours and walls. (14 calculators)
Pitch and angle, true roof area and shingle bundles. (3 calculators)
Board feet, rafters, studs, stairs and deck framing. (6 calculators)
Wire size, voltage drop, conduit fill, duct sizing, generators, fan CFM and room BTU sizing. (7 calculators)
Pipe, pool, septic tank and aquarium volumes in gallons and litres. (4 calculators)
Drywall, paint, wallpaper, tile, grout and flooring quantities. (16 calculators)
Siding of every type, asphalt, epoxy floors, fences, post holes and deck stain. (12 calculators)
Batts, blown-in attic insulation and spray foam costs by R-value. (4 calculators)
How many cubic yards do you need? Works for dirt, mulch, gravel, concrete and any loose material.
Volume plus weight, so you can order by the yard or by the ton.
For slabs, footings and patios — volume in cubic yards, plus bags if you mix by hand.
Bedding sand under pavers is usually 1 inch deep.
For driveways, patches and parking areas — volume in cubic yards, plus tons for ordering.
Fill dirt, garden beds and levelling — volume in cubic yards, plus tons for ordering.
Volume plus weight, so you can order by the yard or by the ton.
Lumber is sold by the board foot — enter thickness, width, length and how many pieces.
Enter rise and run in the same unit — get pitch per 12, roof angle, and rafter length.
Grid rebar for a slab: bars each way, total length and weight. Default bar #4 (0.668 lb/ft).
Minimum tank size by bedrooms, from the common US guideline table. A sizing guide, not a permit — local code decides.
Bricks for a wall, by wall length and height — US modular bricks with standard mortar joints, plus a mortar estimate.
Common rafter length, count and total lumber for a gable roof — from run, pitch, overhang and spacing.
Wall studs for a straight wall run, by wall length and stud spacing.
Gravel and pipe for a French drain trench — cubic yards, tons and pipe length from your trench size.
Concrete for fence and deck post holes — bags per hole and total, with the post's own volume taken out.
Concrete for a set of steps — cubic yards and 80 lb bags from step count, riser, tread and width.
Floor, wall or room area from length and width — in square feet, square yards and square metres, with a coverage cost estimate for flooring or paint.
Topsoil for lawns and garden beds — cubic yards, tons, or bags if the job is small.
Standard 8×8×16 blocks for a wall, by wall length and height — plus the mortar to lay them.
Siding for the outside walls — total wall area minus doors and windows, in square feet and squares.
Mortar mix for laying brick or block — 80 lb bags from how many units you are laying.
True roof surface area from the building footprint and pitch — square feet, roofing squares and shingle bundles.
Tiles for a floor or wall — pick your tile size and get the tile count and boxes to buy.
Insulation bags for an attic floor or wall area — fiberglass batts or blown-in.
Sod for a lawn — square feet, square yards, rolls and pallets from length and width.
Shingle bundles for a roof — enter the actual sloped roof surface dimensions (length × slope width), not the ground footprint.
Wire size for a run — by amps, one-way distance and voltage, sized to keep voltage drop within 3%.
How much water fits in a pipe — from inner diameter and length, in gallons and litres.
Epoxy for a garage or concrete floor — gallons needed, total material cost and cost per square foot.
Fiber-cement (HardiePlank) siding — 12 ft planks for your walls, minus doors and windows.
Wallpaper rolls for a room — wall area from the room size and ceiling height, minus doors and windows.
How much water a pool holds — rectangular, round or oval, from its size and shallow/deep depths.
Grout for a tile floor or wall — 25 lb bags from the area, tile size and joint width.
Blocks for a retaining wall — wall blocks, cap blocks and the gravel base, from wall length and height.
How much water a fish tank holds — gallons and litres from its dimensions, plus what the water weighs.
Mulch for garden beds and around trees — cubic yards in bulk, or 2 cu ft bags for smaller jobs.
Drywall sheets for a room — walls, the ceiling, or both, in 4×8 or 4×12 sheets, plus a rough compound estimate.
Paint for a room's walls — gallons by room size and coats, with doors and windows taken out. Ceiling not included.
Stair layout from the total rise — step count, actual riser, tread depth, total run and stringer length.
Decking boards and joists for a deck — the boards run along the length, so the board count comes from the width.
Posts, sections and rails for a fence — plus the panels or pickets that fill them, by fence length and post spacing.
Voltage drop for a wire run — pick the wire size and see the drop in volts and percent, and whether it stays within the usual 3% guideline.
Heating and cooling size for a room — BTU per hour, AC tons and the closest common mini-split size.
Boxes of flooring for a room — laminate, vinyl plank or hardwood, from the room size and the coverage printed on the box.
Soil for a raised garden bed — cubic yards in bulk, or 1.5 cu ft bags, from the bed size and how deep you fill it.
Blown-in attic insulation top-up — bags and depth to add to go from your current R-value to the target.
Vinyl siding panels for the outside walls — 12.5 ft panels and squares, with doors and windows taken out.
Spray foam cost for a wall, ceiling or rim joist — board feet and total cost for open-cell or closed-cell foam at your thickness.
How deep a fence post hole should be, and what post length to buy — from the fence height and your local frost depth.
Joint compound for taping and finishing drywall — gallons and buckets from the total drywall area.
Recycled asphalt millings for a driveway or parking area — cubic yards and tons from the area and depth.
Boxes of laminate flooring for a room — plus the underlayment rolls to go under it, from the room size and the coverage on the box.
Mapei grout for a tile floor or wall — 25 lb bags from the area, tile size and joint width, for the Keracolor and Ultracolor lines.
Concrete for a strip footing — cubic yards and 80 lb bags from the footing's length, width and depth.
How full is that conduit? Total wire area and fill percentage for up to three THHN wire sizes, checked against the NEC fill limits.
Grass seed for a new lawn or for overseeding — pounds and bags from your lawn area and grass type.
Concrete for round tube footings (Sonotube-style forms) — cubic yards and 80 lb bags from the tube size, depth and how many footings.
Pea gravel for walkways, patios and play areas — cubic yards, tons, or bags for smaller jobs.
River rock for landscape beds, borders and drainage areas — cubic yards, tons, or bags for smaller jobs.
Countertop square footage and cost — one or two sections, priced by the material you pick. Prices are typical installed estimates.
Grout or concrete to fill the cores of a concrete block wall — and the block count itself — by wall size, block size and how many cores get filled.
Duct size for an airflow — the round diameter you need, the standard size to actually buy, and the rectangular ducts that match it.
What size generator do you need? Tick off the appliances you want to run during an outage — quantities included — and get the size to buy.
Balusters for a deck or stair railing — how many you need, and the exact even spacing that keeps every gap within the code limit.
Pavers for a patio or walkway — the count by paver size, plus the compacted gravel base and bedding sand that go underneath them.
Polymeric joint sand for a paver patio or walkway — 50 lb bags from the area and the width of the joints between the pavers.
Ramp slope from a rise and a run — the ratio, the grade percent and the angle, and whether the slope stays within the 1:12 maximum for an accessible ramp.
Exhaust fan size for a room — the CFM the fan needs to move, from the room's volume and how many air changes per hour that kind of room wants.
Installed carpet cost for a room — the square yards you are buying and a total price by carpet type, with old-carpet removal added if you need it.
What carpet cleaning should cost — an estimate from the carpet area and the cleaning method, with the usual minimum service charge built in.
What sanding and refinishing a hardwood floor should cost — figured on the floor area and rate per square foot, with stairs priced per step.
Thinset mortar for a tile job — 50 lb bags from the area and tile size, with the trowel notch that tile size calls for.
Stain for a deck, porch or fence run of decking — gallons and cans from the deck area, how many coats you plan, and the coverage printed on the can.
Concrete for deck footings — the footing count for a simple grid layout, and the concrete to fill them, in cubic yards and 60 lb bags.
Blown-in insulation for an attic floor — bags of blown fiberglass or cellulose to hit a target R-value, figured from the manufacturer's bag coverage chart.
Stain for a fence — gallons and cans from the fence length and height, how many sides you are staining, and the coverage printed on the can.
Ceiling tiles for a room — pick 2 × 2 ft or 2 × 4 ft tiles and get the count to buy, for a drop ceiling or a glue-up ceiling.
Rubber mulch for play areas, beds and borders — 40 lb bags from the area and the depth you want, figured on the standard bag coverage.
Palings for a timber paling fence — the paling count, posts and rails from the fence length, paling width and the gap between palings. Metric-first, with a feet option for the length.